Glossary Letter F
Metal straps that are used to repair a bearing wall "cut-out", and to "tie together" wall corners, splices, and bearing headers. Also, they are used to hang stairs and landings to bearing headers.
To install nails into the vertical face of a bearing header or beam.
To finish the front and all vertical sides of a concrete porch, step(s), or patio. Normally the "face" is broom finished.
The brick used and exposed on the outside of a wall. Usually these have a finished texture.
Horizontal boards attached to rafter/truss ends at the eaves and along gables. Roof drain gutters are attached to the fascia.
Tar paper. Installed under the roof shingles. Normally 15 lb. or 30 lb.
Any part, such as a nut or fitting, into which another (male) part can be inserted. Internal threads are female.
Metal tubes used to keep roof gutters "open". Long nails (ferrule spikes) are driven through these tubes and hold the gutters in place along the fascia of the home.
To take measurements (cabinets, countertops, stairs, shower doors, etc.) in the home itself instead of using the blueprints.
A manufacturing process of interlocking two shorter pieces of wood end to end to create a longer piece of dimensional lumber or molding. Often used in jambs and casings and are normally painted (instead of stained).
Short horizontal members sometimes nailed between studs, usually about halfway up a wall. See also 'Fire stop'.
Brick made of refractory ceramic material which will resist high temperatures. Used in a fireplace and boiler.
A large sheet of metal that is installed around and perpendicular to the fireplace flue pipe. It's purpose is to confine and limit the spread of fire and smoke to a small area.
Applies to materials that are not combustible in the temperatures of ordinary fires and will withstand such fires for at least 1 hour. Drywall used in the garage and party walls are to be fire rated, 5/8", Type X.
A chemical or preparation of chemicals used to reduce the flammability of a material or to retard the spread of flame.
A solid, tight closure of a concealed space, placed to prevent the spread of fire and smoke through such a space. In a frame wall, this will usually consist of 2 by 4 cross blocking between studs. Work performed to slow the spread of fire and smoke in the walls and ceiling (behind the drywall). Includes stuffing wire holes in the top and bottom plates with insulation, and installing blocks of wood between the wall studs at the drop soffit line. This is integral to passing a Rough Frame inspection. See also 'Fire block'.
A wood or plywood piece used to fasten the ends of two members together at a butt joint with nails or bolts. Sometimes used at the junction of opposite rafters near the ridge line. Sometimes called a gang nail plate.
A long strip of spring steel used for fishing cables and for pulling wires through conduit.
A contract with a set price for the work. See Time and Materials Contract.
A loan where the initial payments are based on a certain interest rate for a stated period . The rate payable will not change during this period regardless of changes in the lender's standard variable rate.
A mortgage with an interest rate that remains the same over the years.
Flat stones (1 to 4 inches thick) used for walks, steps, floors, and vertical veneer (in lieu of brick).
A manufactured wood panel made out of 1"- 2" wood chips and glue. Often used as a substitute for plywood in the exterior wall and roof sheathing. Also called OSB or wafer board.
An oil burner, designed to hold the flame near the nozzle surface. Generally the most efficient type for residential use.
Sheet metal or other material used in roof and wall construction to protect a building from water seepage.
Thin wood strips installed over the butt seam of cabinet skins.
An interior paint that contains a high proportion of pigment and dries to a flat or lusterless finish.
Common word for concrete floors, driveways, basements, and sidewalks.
The next-to-last stage in concrete work, when you smooth off the job and bring water to the surface by using a hand float or bull float.
A non-bearing wall built on a concrete floor. It is constructed so that the bottom two horizontal plates can compress or pull apart if the concrete floor moves up or down. Normally built on basements and garage slabs.
A fluorescent lamp is a gas-filled glass tube with a phosphur coating on the inside. Gas inside the tube is ionized by electricity which causes the phosphur coating to glow. Normally with two pins that extend from each end.
Large pipe through which fumes escape from a gas water heater, furnace, or fireplace. Normally these flue pipes are double walled, galvanized sheet metal pipe and sometimes referred to as a "B Vent". Fireplace flue pipes are normally triple walled. In addition, nothing combustible shall be within one inch from the flue pipe.
Round metal ring which fits around the heat flue pipe after the pipe passes out of the roof.
An automatic door located in the flue that closes it off when the burner turns off; purpose is to reduce heat loss up the flue from the still-warm furnace or boiler.
2-foot lengths, fire clay or terra-cotta pipe (round or square) and usually madein all ordinary flue sizes. Used for the inner lining of chimneys with the brick or masonry work done around the outside. Flue linings in chimneys runs from one foot below the flue connection to the top of the chimney.
End rafters of the gable overhang supported by roof sheathing and lookouts.
Continuous 8" or 10" thick concrete pad installed before and supports the foundation wall or monopost.
A common form of heating with natural gas, propane, oil or electricity as a fuel. Air is heated in the furnace and distributed through a set of metal ducts to various areas of the house.
Temporary structure erected to contain concrete during placing and initial hardening.
The supporting portion of a structure below the first floor construction, or below grade, including the footings.
Metal wires that hold the foundation wall panels and rebar in place during the concrete pour.
High-quality below-grade moisture protection. Used for below-grade exterior concrete and masonry wall damp-proofing to seal out moisture and prevent corrosion. Normally looks like black tar.
The act of inspecting the home's structural integrity and it's complianceto local municipal codes.
The carpenter contractor that installs the lumber and erects the frame, flooring system, interior walls, backing, trusses, rafters, decking, installs all beams, stairs, soffits and all work related to the wood structure of the home. The framer builds the home according to the blueprints and must comply with local building codes and regulations.
Lumber used for the structural members of abuilding, such as studs, joists, and rafters.
In house construction a horizontal member connecting the top of the siding with the soffit of the cornice.
Round metal lid that is installed on a water meter pit.
The depth of frost penetration in soil and/or the depth at which the earth will freeze and swell. This depth varies in different parts of the country.
Strips of wood, often 1 X 2 and used to shim out and provide a level fastening surface for a wall or ceiling.
A device often found in older homes designed to prevent overloads in electrical lines. This protects against fire. See also'circuit breakers'.